Double acting hydraulic cylinders HVB
Other products
How to choose a Double acting hydraulic cylinders HVB Guide ?
Access Double acting hydraulic cylinders HVB 's products
Access selection
Back to Hydraulic block cylinders
Double acting hydraulic cylinders HVB FTT
(CNOMO type)
Operating pressure: 200 bar
Bare cylinder, fastened by tapped holes on rod side.
Operating pressure :
Max. supply pressure: 200 bar
Test pressure: 315 bar
Permissible speed: Max. speed 5 m/min
Temperatures :
Minimum: -20°C
Maximum: +80°C with Standard seal, +150°C with Viton seal.
Fluids :
HM-HL hydraulic mineral oils 10 to 40 Cst at 50°C.
Low flammability fluids class C or D
Filtration: ≤ 200 microns
Connection: In BSPP cylindrical gas with counterbore for sealing ring.
Commissioning:
To ensure correct operation, air in both cylinder chambers should be purged by loosening the fittings, oil unpressurized. When the fluid is free of emulsion, retighten the fittings.
| Bore | Units | 25 | 32 | 40 | 50 | 63 | 80 | 100 | 125 |
| ød (ø Rod) | (mm) | 16 | 18 | 22 | 28 | 36 | 45 | 56 | 70 |
| øf | (mm) | 36 | 40 | 45 | 56 | 63 | 80 | 100 | 125 |
| P | (mm) | 12 | 12 | 12 | 12 | 18 | 18 | 24 | 24 |
| b | (mm) | 45 | 56 | 63 | 75 | 85 | 106 | 125 | 160 |
| p | G1/8 | G1/8 | G1/4 | G1/4 | G3/8 | G3/8 | G1/2 | G1/2 | |
| øLa | (mm) | 19 | 19 | 25 | 25 | 28 | 28 | 34 | 34 |
| x | (mm) | 34 | 45 | 45 | 53 | 56 | 63 | 70 | 80 |
| TA | M6 | M8 | M10 | M10 | M12 | M16 | M18 | M20 | |
| s | (mm) | 34 | 42 | 45 | 56 | 65 | 80 | 97.5 | 125 |
| t | (mm) | 34 | 42 | 45 | 56 | 65 | 80 | 97.5 | 125 |
| c | (mm) | 16 | 20 | 25 | 28 | 28 | 32 | 38 | 40 |
| v | (mm) | 28 | 32 | 40 | 40 | 45 | 50 | 58 | 63 |
| y | (mm) | 46 | 48 | 55 | 57 | 71 | 74 | 81 | 93 |
| L | (mm) | 92 | 102 | 115 | 125 | 145 | 152 | 177 | 198 |
Strokes
| Bore | 25 | 32 | 40 | 50 | 63 | 80 | 100 | 125 | |
Stroke Tolerance+2 0 |
5 | X | X | X | X | X | X | X | X |
| 10 | X | X | X | X | X | X | X | X | |
| 16 | X | X | X | X | X | X | X | X | |
| 25 | X | X | X | X | X | X | X | X | |
| 40 | X | X | X | X | X | X | X | X | |
| 63 | X | X | X | X | X | X | X | ||
| 100 | X | X | X | X | X | X | X | ||
| 160 | X | X | X | X | X | X | |||
Rod ends
| Bore | Units | 25 | 32 | 40 | 50 | 63 | 80 | 100 | 125 |
| ød (ø Rod) | (mm) | 16 | 18 | 22 | 28 | 36 | 45 | 56 | 70 |
| ød / Al | (mm) | 10 | 10 | 12 | 12 | 12 | 12 | 16 | 16 |
| A | (mm) | 20 | 20 | 25 | 32 | 40 | 50 | 63 | 80 |
| øR | (mm) | 9.5 | 9.5 | 13 | 17 | 23.5 | 29.5 | 38.5 | 48.5 |
| øCl | (mm) | 9.5 | 9.5 | 11.5 | 11.5 | 11.5 | 11.5 | 15 | 15 |
| i | (mm) | 2.5 | 2.5 | 3 | 3 | 3 | 4 | 5 | 5 |
| M | (mm) | M12 x 1.25 | M12 x 1.25 | M16 x 1.5 | M20 x 1.5 | M27 x 2 | M33 x 2 | M42 x 2 | M56 x 2 |
| C | (mm) | M8 x 1.25 | M8 x 1.25 | M10 x 1.5 | M16 x 1.5 | M20 x 1.5 | M27 x 2 | M33 x 2 | M42 x 2 |
| Ml | (mm) | M8 x 1.25 | M8 x 1.25 | M10 x 1.25 | M10 x 1.5 | M10 x 1.5 | M10 x 1.5 | M12 x 1.25 | M12 x 1.25 |
| n | (mm) | 0.2 | 0.2 | 0.2 | 0.2 | 0.3 | 0.3 | 0.5 | 0.5 |
| øE | (mm) | 14 | 15 | 18 | 22.5 | 28 | 35.5 | 45 | 56 |
| øF | (mm) | 8 | 9 | 11.2 | 14 | 18 | 22.4 | 28 | 35.5 |
| H/J | (mm) | 6 | 6 | 8 | 10 | 12.5 | 16 | 20 | 25 |
| r | (mm) | 0.3 | 0.3 | 0.5 | 0.5 | 0.8 | 0.8 | 1.2 | 1.2 |
| B | (mm) | 8 | 8 | 8 | 8 | 12.5 | 12.5 | 14 | 14 |
| Bl | (mm) | 5 | 5 | 6 | 6 | 6 | 6 | 8 | 8 |
| K | (mm) | 12 | 13 | 17 | 22 | 30 | 36 | 46 | 60 |
| Ki | (mm) | 8 | 8 | 10 | 10 | 10 | 10 | 13 | 13 |
Information rod
| Bore | Units | 25 | 32 | 40 | 50 | 63 | 80 | 100 | 125 |
| ød (ø Rod) | (mm) | 16 | 18 | 22 | 28 | 36 | 45 | 56 | 70 |
| a | (mm) | 45 | 56 | 63 | 75 | 85 | 106 | 125 | 160 |
| øBi | (mm) | 36 | 36 | 42 | 42 | 63 | 63 | 80 | 80 |
| ødi | (mm) | 10 | 10 | 12 | 12 | 12 | 12 | 16 | 16 |
| Ui | (mm) | 8 | 8 | 12 | 12 | 12 | 12 | 15 | 15 |
| Li | (mm) | 20 | 20 | 32 | 32 | 32 | 32 | 35 | 35 |
| L | (mm) | 92 | 102 | 115 | 125 | 145 | 152 | 177 | 198 |